Report Cams Down and Forum Errors
Re: Report Cams Down and Forum Errors
WHITE ROCK
CU patrol is wonky again . Can't remember how it was fixed last time?
CU patrol is wonky again . Can't remember how it was fixed last time?
Re: Report Cams Down and Forum Errors
2:02pm
Looks like the East embedded cam at Delta2 is frozen at 12:49pm. Very windy again (it seems).
2:09pm now it seems to have jumped ahead to 1:13pm.
Looks like the East embedded cam at Delta2 is frozen at 12:49pm. Very windy again (it seems).
2:09pm now it seems to have jumped ahead to 1:13pm.
“The eyesight for an eagle is what thought is to a man.”
― Dejan Stojanovic, The Creator
― Dejan Stojanovic, The Creator
Re: Report Cams Down and Forum Errors
If the presets aren't taking you to the correct location, I can try to recalibrate the cam (I think that's term) - doing that will help if the cam got jiggled or bumped so its internal compass got upset (or whatever it uses as a starting point to know where all the other settings are located). When we had a cam at the Lafarge factory, it was on a building that vibrated when they ran certain processes - and it needed to be recalibrated fairly often.
That will only help if it's a software issue. If the cam has actually moved, I should recalibrate it first, but you probably will need to redo the presets.
If "wonky" means something other than going to the wrong place when you use a preset, I'll need more details to figure out how to fix it.
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
I get "video unavailable" when I try to view the embedded cam. The cam itself was fine when I logged in to check (and showed the current time) - at least after I switched the control window to the lower resolution Sub Stream setting.
I've sent a message to Ken.
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
Thanks Judy... yes it's changed again since I last added to this, to "video unavailable", as you say.JudyB wrote: ↑Tue Nov 29, 2022 2:47 pmI get "video unavailable" when I try to view the embedded cam. The cam itself was fine when I logged in to check (and showed the current time) - at least after I switched the control window to the lower resolution Sub Stream setting.
I've sent a message to Ken.
“The eyesight for an eagle is what thought is to a man.”
― Dejan Stojanovic, The Creator
― Dejan Stojanovic, The Creator
Re: Report Cams Down and Forum Errors
thinking its that the presets aren't taking me to the correct location .JudyB wrote: ↑Tue Nov 29, 2022 2:37 pmIf the presets aren't taking you to the correct location, I can try to recalibrate the cam (I think that's term) - doing that will help if the cam got jiggled or bumped so its internal compass got upset (or whatever it uses as a starting point to know where all the other settings are located). When we had a cam at the Lafarge factory, it was on a building that vibrated when they ran certain processes - and it needed to be recalibrated fairly often.
That will only help if it's a software issue. If the cam has actually moved, I should recalibrate it first, but you probably will need to redo the presets.
If "wonky" means something other than going to the wrong place when you use a preset, I'll need more details to figure out how to fix it.
I can't check with NORTH to get a look at CU housing to see if it shifted. You checked last time this happened and could confirm the housing was same as when it was installed.
Re: Report Cams Down and Forum Errors
Thanks! I'll log into North for a quick look, and then I'll log into CU to try recalibrating it again.
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
I am out of both cams - and good news! I think Calibrate solved the problem. I tried a couple of presets first, and they did not go where they should - and after I ran Calibrate, I tried them again, and they look pretty good to me.
I posted a picture of the CU cam from the North cam on the White Rock thread - but my guess is that all the wind we've been having didn't move the cam, but shook it enough that it sort of forgot where it was (that's the non-technical term ).
Anyway, I think it's fixed - but if not, please let me know and we'll look a little deeper.
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
7.30a WR/ WA is frozen
Re: Report Cams Down and Forum Errors
Thanks, Amy! WA is streaming now (7:46 am) but CU is frozen at 5:13 am for me, so I'll let Ken know.
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
Hi Judy Cam is back at H Mills
11:02am From the NPTZ Cam Thanks
Bev
11:02am From the NPTZ Cam Thanks
Bev
Re: Report Cams Down and Forum Errors
White Rock CU cam stream on YouTube is frozen at 9:12am. Now 11:33am.
Thanks for help
Thanks for help
Re: Report Cams Down and Forum Errors
Thanks for the call, Bev - embedded cam is back!
2023 Eaglet Info ~ ~ ~ ~ ~ Helpful Hints
Re: Report Cams Down and Forum Errors
You are welcome Judy and thanks !
Re: Report Cams Down and Forum Errors
WHITE ROCK .
aT 10:52 am - WA live stream stopped.
aT 10:52 am - WA live stream stopped.